Thompson Water Seal Timber Oi Clar L Review
Thompson's® WaterSeal® Clear Multi-Surface Waterproofer
- Print This Page
Clear Multi-Surface Waterproofer
Proven to waterproof woods, concrete and brick. Utilise as a wood sealer, brick sealer, or for concrete waterproofing.
Key Features
- Prevents Water Damage
- Allows Forest to Grayness Naturally
Gauge Coverage
- See chart below
More Details
Actual coverage will vary considerably due to porosity of surface materials.
| Fabric | Approximate Coverage (sq. ft./gal.) |
|---|---|
| Brick | 175 |
| Concrete | 250 |
| Shine Concrete Block | fifty |
| *Clay Tile & Quarry Tile Stucco | 250 |
| *Slate - Masonite | 375 |
| Forest: Rough Sawn | 100 |
| Wood: Smooth Finish | 200 |
| Plywood | 150 |
| Wood Shingles | 100 |
*Wipe surface dry out after 5-x minutes.
Directions for Apply
Before You lot Begin
- For exterior utilize simply.
- Exist sure that both surface and air temperatures are above l°F during application and remain above 40°F for 48 hours afterward application. Do not employ production if rain is forecasted within 24 hours of application.
- Perform the splash test. Sprinkle h2o on various sections of surface to be sealed. If water absorbs and darkens color of substrate inside five seconds, surface is porous and considered ready to be treated. If water beads upwards or otherwise sits on acme of surface, then surface does not need protection at this fourth dimension.
- Cover plants and shrubs. Motility all objects that could come up in contact with overspray. Wet overspray of product tin be removed by flushing immediately with water. Stale overspray can be removed with pigment thinner or mineral spirits, following manufacturer'due south safety recommendations.
- Exercise not use in below grade application where water pressure is a trouble, or on painted or recently stained surfaces.
- DO Not Utilize Every bit AN Condiment TO PAINT.
- Protect product from freezing. Do not store below 32°F. In case of adventitious freezing, call The Thompson's Company Aid Line.
Surface Preparation
- Surfaces and substrates must be complimentary of all mildew, dust, clay, oil, soot, grease and other contaminants.
- For Concrete/Brick/Masonry : Surfaces must be thoroughly cleaned prior to application with a concrete cleaner applied according to label directions and cautions. Concrete that has a polish, flat finish must be opened for proper penetration. This should exist done using a concrete etch product. Follow etching product use instructions carefully and ensure thorough rinsing and removal of etching solution. Permit physical to dry out a minimum of 72 hours afterwards etching before applying a waterproofer.
- For Wood : Surfaces must be thoroughly cleaned prior to awarding with a deck cleaner (like those in the Thompson's ® WaterSeal ® cleaner line) practical co-ordinate to label directions and cautions. In one case wood surface has been cleaned, wait iii hours before applying Thompson's ® WaterSeal ® Clear Multi-Surface Waterproofer.
Application
- Do not mix with other waterproofing products; variations in the last appearance may result.
- Practise not thin.
- Concrete/Stucco must exist completely cured (minimum of 4 weeks) and dry.
- Shake contents well before use.
- A minor trial patch should exist tried earlier application over the unabridged surface.
- Only one light coat is necessary in about applications.
- Apply past brush, roller, or sprayer. A garden "pump-up" fashion sprayer is the simplest method. Production will appear milky white during application, but will dry articulate.
- If puddling of product occurs, remove inside 15 minutes by redistributing to dry areas or wiping off.
- Use only with acceptable ventilation.
- Tackiness will result if over-applied. May likewise occur later on awarding if overnight temperature falls below xl°F within 48 hours of application.
Drying
- Allow at least 24 hours to dry; yet drying time will vary depending on the substrate, temperature, and humidity. When completely dry, perform the splash test to decide if 2nd glaze is necessary.
- Allow 45 days drying time before applying latex paint over Thompson'south® WaterSeal® Clear Multi-Surface Waterproofer.
- Allow a minimum of three days drying fourth dimension before applying oil based paint over Thompson's® WaterSeal® Clear Multi-Surface Waterproofer.
- Length of protection will vary depending on environs. Perform the splash exam once a yr to see whether reapplication is necessary. Vertical and horizontal surfaces will experience color changes at unlike rates.
Make clean Up
- Clean brushes and equipment with mineral spirits following manufacturer'due south rubber recommendations, and then rinse with soap and clean water.
Cautions
CAUTIONS: Utilise only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or habiliment respiratory protection (NIOSH approved) or get out the area. Avoid contact with eyes and skin. Wash hands later using. Go on container closed when not in use. Do non transfer contents to other containers for storage. FIRST Assistance: In case of eye contact, flush thoroughly with large amounts of water. Get medical attending if irritation persists. If swallowed, telephone call Toxicant Control Heart, hospital emergency room, or physician immediately. Alert: This product contains chemicals known to the Land of California to cause cancer and nascence defects or other reproductive harm. DO NOT TAKE INTERNALLY. Keep OUT OF THE Accomplish OF CHILDREN.
Reviews
Source: https://www.thompsonswaterseal.com/waterproofing-products/multisurface-waterproofers/clear-multi-surface-waterproofer